Waldorf MicroWave XT Bedienungsanleitung Seite 39
- Seite / 126
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Oscillators
The oscillators are the first unit in the chain of the MicroWave II/XT/XTk’s sound generation.
In comparison to a classic analog synthesizer, the oscillator’s output signal itself is not used
as a sound source. It is the driving element for the wavetable synthesis.
Oscillator 1
Osc 1 / 1
Osc 1 / 2
Octave
-4…+4
Determines the octave setting of the oscillator. The reference pitch for the oscillator is
generated at MIDI note A3 (note no. 69) when Octave, Semitone and Detune is set to
0
and Keytrack is
100%
. In this case the oscillator’s frequency will be the same as set in the
global Tune parameter (normally 440Hz). Set this parameter to
0
if you are creating a
typical keyboard sound, set it to
-1
for bass sounds. If you are programming strings or other
high pitched sound, set Octave to
+1
. The following table shows the relationship between
the Octave setting and its corresponding register value, a common measurement based on
the length of organ pipes.
Semitone
-12...+12
Determines the pitch of the oscillator in semitone steps. The standard setting for this
parameter is
0
, but there are cases where different values are required: Most organ sounds
include a quint, therefore one oscillator's semitone parameter must be set to
+7
. There are
also many lead sounds with an interval, e.g. a quart (+5 semitones). When making ring
modulated sounds, try to use
+11
for the setting.
Detune
-64…+63
Fine-tunes the oscillator in increments of 128ths of a semitone. The audible result of
detuning oscillators is a flanging. Use a positive setting for one oscillator and an equivalent
negative setting for the other. A low value of
±1
results in a slow and soft flange effect. Mid-
ranged settings of
±5
are optimal for pads and other fat sounding programs. High values of
±12
or above will give a strong detune that can be used for accordeons or effect sounds.
Setting Register
-4
128ft.
-3
64ft.
-2
32ft.
-1
16ft.
0
8ft.
+1
4ft.
+2
2ft.
+3
1ft.
+4
1/2ft.
Pitchbend Range 1|FM Amount
02 | 010
Octave 1|Semitone | Detune |Keytrack
-2 | +07 | +00 | +100%
User’s Manual MicroWave II • MicroWave XT • XTk
39
- Bedienungsanleitung 1
- User's Manual 1
- Garantiekarte / Warranty Card 3
- Contents 5
- Diagrams 6
- Front Panel 7
- Rear Panel 7
- Foreword 10
- -2 11
- General Safety Guidelines 12
- Maintenance 13
- Proper Use 13
- Inventory 14
- Connections 14
- Analog Input 15
- Quick Start 16
- Saw Repeat WMF 16
- 01 16
- Store Sound A001 A001 ? 17
- Saw Repeat WMF 17
- 092 17
- Multi Mode 20
- Activating the Instrument 21
- Building a layered Sound 22
- Operation 23
- Editing Parameters 25
- Saw repeat WMF 26
- -1 26
- Edit Buffers 27
- The Compare Function 27
- Recalling Edits 28
- Storing Programs 28
- The Play Access Page 29
- Panic Function 30
- Randomizing a Program 30
- Initializing Programs 30
- Init Multi 31
- About Wavetable Synthesis 33
- Overview 34
- Wavetable 35
- What else can we do? 36
- Creating own Wavetables 37
- Overview of Functions 38
- Oscillators 39
- Oscillator 2 40
- Oscillator 1 42
- Oscillator 2 in Sync 42
- 001...128 43
- 065…128 43
- 065…096 43
- Wave 2 / 1 45
- Wave 2 / 2 45
- 3 47
- External 48
- 113 48
- Play Access 49
- Example 1 50
- Example 2 50
- Example 3 50
- Example 4 50
- Frequency 51
- Resonance 51
- Filter 1 52
- Filter Types 53
- 12db High Pass 54
- Filter 1 / 2 55
- 24dB Notch Filter 56
- 12dB Notch Filter 56
- Bandstop Filter 56
- Filter 2 56
- -200%…+197% 57
- Amplifier 58
- 090 58
- Panning 59
- Effect 60
- Chorus 60
- MicroWave II MicroWave XT 60
- Flanger 1 61
- Flanger 2 61
- AutoWahLP 61
- AutoWahBP 62
- Overdrive 62
- Amp. Mod 63
- Pan Delay 63
- Effect 64
- Mod Delay 64
- Active 65
- Trigger 1 66
- Trigger 2 66
- Arpeggiator 68
- Position 71
- 03 71
- Arpeggiator User Pattern 71
- Filter Env 72
- 000 72
- Amplifier Env 73
- Wave Envelope 74
- Free Envelope 77
- LFO 1 / 1 78
- LFO 1 / 2 78
- LFO 2 / 1 79
- LFO 2 / 2 79
- Modifier Delay 81
- Modifier Units 82
- Mod 1…16 85
- Modwheel 85
- Program Name 86
- Multi parameters 87
- Instrument parameters 88
- Key Velocity 95
- Velocity 95
- MIDI Control 97
- Sending System Exclusive Data 98
- Updating the System Software 100
- Converting MicroWave Sounds 101
- Appendix 102
- Software release 2.28 103
- System Exclusive Data Format 106
- Glossary 117
- MIDI Implementation Chart 122
- FCC Information (U.S.A.) 124
Verwandte Produkte und Handbücher für Synthesizer Waldorf MicroWave XT
Synthesizer Waldorf Pulse Bedienungsanleitung
(78 Seiten)
(78 Seiten)
Synthesizer Waldorf XTk Bedienungsanleitung
(132 Seiten)
(132 Seiten)
Synthesizer Waldorf Pulse Bedienungsanleitung
(11 Seiten)
(11 Seiten)
Synthesizer Waldorf Pulse Bedienungsanleitung
(19 Seiten)
(19 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.226 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern